pumpexpress.co.uk

HF Centrifugal Transfer Pump Range (High Flow) General Product Description

PK End Suction Pump
Further Product Info

HF Pump Performance Curve
HF Pump Performance Data
HF Pump Dimensions
Get the bigger picture

PERFORMANCE RANGE

Flow rate up to 1800 L/min (108 m³/hr)
Dynamic head up to 24.5 m

PUMP INSTALLATION AND APPLICATIONS

HF pumps are specifically designed for domestic, agricultural and industrial use. Their performance levels, mechanical design and structural materials are explicitly selected for these uses. The shapes of their volutes and impellers, with large passages, make them suitable for pumping even fairly dirty water.

HF PUMPS CAN ACHIEVE HIGH DELIVERY RATES UNDER CONTINUOUS OR HEAVY DUTY, MAKING THEM ADVANTAGEOUS FOR RAIN AND GRAVITY IRRIGATION, FOR PUMPING WATER FROM LAKES, RIVERS, WELLS AND FOR A WIDE VARIETY OF INDUSTRIAL USES WHERE HIGH DELIVERY RATES MUST BE ACHIEVED AT LOW TO AVERAGE HEADS.
THEY CAN ALSO BE USED FOR THE TRANSFER OF DIESEL FUEL.

These pumps should be installed in a covered area, protected against the weather.

PERFORMANCE

HF pumps come in a wide and diverse range, making it easy to select the model most suited to each requirement. Special design efforts were made to unify the entire HF series which is distinctive for its:

  • very high flow rates from low motor power, flat performance curves.
  • non-surging phenomena, even when pumping near minimum flow rates
  • flat absorption curves at high delivery rates, to prevent motor overloading even during prolonged use at high rates.
  • good suction capabilities at both low and high delivery rates.

Curve tolerance according to ISO 2548.

STRUCTURAL CHARACTERISTICS

  • Cast iron PUMP BODY with UNI ISO 228/1 gas threaded suction and delivery ports.
  • Open BRASS IMPELLER.
  • AISI 316 stainless steel MOTOR SHAFT (AISI 416 up to 0.75 kW).
  • Ceramic and graphite MECHANICAL SEAL
  • MOTOR: pumps are coupled directly to an asynchronous, high efficiency PEDROLLO induction motor of suitable size, which is quiet running, closed and externally ventilated, suitable for continuous duty.
    INSULATION class F (B up to 0.75 kW and 1.1 kW three phase).
    A thermal cutout relay (motor protector) is incorporated in single phase motors.

Three phase motors require an adequate external motor protector, and connections are to be according to current standards.

  • PROTECTION IP 44.
  • CONSTRUCTION AND SAFETY STANDARDS in compliance with EN 60 335 -1, (IEC 335-1, CEI 61-150) EN 60034-1 (IEC 34-1, CEI 2-3).

PERFORMANCE CURVE

PERFORMANCE DATA

PERFORMANCE DATA AT=2900 l/min
PUMP MODEL POWER Q
m³/h		 0 6 12 18 24 30 36 42 48 54 60 66 72 78 84 90
Single Phase Three Phase KW HP l/min 0 100 200 300 400 500 600 700 800 900 1000 1100 1200 1300 1400 1500
HFm 4 HF 4 0.75 1 Hm 10 9.8 9.3 8.7 8 7 6 4.7 3              
HFm 6C HF 6C 1.1 1.5 11.9 - 11.7 11.3 10.7 10.2 9.2 8 6.7 5 3          
HFm 6B HF 6B 1.5 2 14.7 - 14.5 14 13.5 12.8 12 11 9.7 8.2 6.7 5        
_____ HF 6A 2.2 3 18.5 - 18.1 17.8 17.2 16.8 16 15 13.8 12.2 10.5 8.3 6      
HFm 6CR HF 6CR 1.1 1.5 11.9 - 11.7 11.3 10.7 10.2 9.2 8 6.7 5 3          
HFm 6BR HF 6BR 1.5 2 14.7 - 14.5 14 13.5 12.8 12 11 9.7 8.2 6.7 5        
_____ HF 6AR 2.2 3 18.5 - 18.1 17.8 17.2 16.8 16 15 13.8 12.2 10.5 8.3 6      
HFm 8B HF 8B 3 4 21.5 - 21 20.7 20 19.5 18.8 17.8 16.5 15 13.5 11.2 9      
_____ HF 8A 4 5.5 24.5 - 24 23.5 23 22.5 21.8 20.8 19.5 18.3 16.8 15 13      
PUMP MODEL POWER Q
m³/h		 0 24 30 36 42 48 54 60 66 72 78 84 90 96 102 108
Single Phase Three Phase KW HP l/min 0 400 50 600 700 800 900 1000 1100 1200 1300 1400 1500 1600 1700 1800
HFm 20B HF 20B 3 4 Hm 16 15.5 15.4 15.3 15.2 15 14.5 14 13 12 10.7 9 7 4.8 2  
_____ HF 20A 4 5.5 19 18.5 18.4 18.3 18.2 18 17.5 17 16.2 15.2 13.7 12 10 7.8 5 2
H = TOTAL DYNAMIC HEAD IN METRES
Q = FLOW RATE

PRODUCT DIMENSIONS

PUMP MODEL DN1 DN2 Dimensions mm
Single Phase Three Phase a f h h1 h2 n n1 w s
HFm 4 HF 4 2½" 2½" 55 323 140 97 143 190 155 - 10
HFm 6C HF 6C 3" 3" 68 385 312 120 192 240 190 6 12
HFm 6B _____ 3" 3" 68 405 312 120 192 40 190 6 12
_____ HF 6B 3" 3" 68 385 312 120 192 240 190 6 12
_____ HF 6A 3" 3" 68 405 312 120 192 40 190 6 12
HFm 6CR HF 6CR 4" 4" 70 387 312 120 192 240 190 6 12
HFm 6BR _____ 4" 4" 70 407 312 120 192 240 190 6 12
_____ HF 6BR 4" 4" 70 387 312 120 192 240 190 6 12
_____ HF 6AR 4" 4" 70 407 312 120 192 240 190 6 12
HFm 8B HF 8B 4" 4" 80 429 312 132 180 245 190 30 14
_____ HF 8A 4" 4" 80 475 312 132 180 245 190 30 14
HFm 20B HF 20B 4" 4" 80 429 312 132 180 245 190 30 14
_____ HF 20A 4" 4" 80 475 312 132 180 245 190 30 14
Click Here